Bay 12 Games Forum

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Issue with digging upwards?  (Read 592 times)

TotalPigeon

  • Bay Watcher
    • View Profile
Issue with digging upwards?
« on: October 29, 2007, 08:20:00 pm »
After I place an upwards ramp and change the view to the new level, if I select any of the now exposed rock for mining it just gets completely ignored. I don't get the same problem if I go down, however... which seems a little strange. Anyone else getting anything like this, or are you all too busy digging right down? lol
Logged

Fourth Triad

  • Bay Watcher
    • View Profile
    • http://www.bay12games.com
Re: Issue with digging upwards?
« Reply #1 on: October 29, 2007, 08:22:00 pm »
you have to channel out the square above it, after building the ramp to get the ramp to work

[ October 29, 2007: Message edited by: Fourth Triad ]

Logged

Sowelu

  • Bay Watcher
  • I am offishially a penguin.
    • View Profile
Re: Issue with digging upwards?
« Reply #2 on: October 29, 2007, 08:22:00 pm »
Just a guess (still at work), but ramps might need a different tile designated--up+forward or something?

But as a workaround, well, the movies seemed to work fine with stairs, so maybe you just need stairs first to build the upper level in the first place.

Logged
Some things were made for one thing, for me / that one thing is the sea~
Quote from: nenjin on April 20, 2012, 10:44:40 am
His servers are going to be powered by goat blood and moonlight.
Quote from: PTTG?? on April 20, 2012, 10:48:33 am
Oh, a biomass/24 hour solar facility. How green!

TotalPigeon

  • Bay Watcher
    • View Profile
Re: Issue with digging upwards?
« Reply #3 on: October 29, 2007, 08:29:00 pm »
So (fourth triad) you're saying you have to dig out the floor before you can dig out the rest? Thing is, I can see the ramp from that floor, they just ignore the walls around it. I'll give it a go though (tomorrow)

I also tried upwards stairs, but I can't even see that from the floor above and any digs around it are also ignored.

Logged

Fourth Triad

  • Bay Watcher
    • View Profile
    • http://www.bay12games.com
Re: Issue with digging upwards?
« Reply #4 on: October 29, 2007, 08:42:00 pm »
it only works with ramps and only after you build ramp can the dwarves reach the ceiling, with stairs you have to have matching sets of up and down stairs for them to work, but yeah ramps are very unintuitive to use

[ October 29, 2007: Message edited by: Fourth Triad ]

Logged

THLawrence

  • Bay Watcher
  • Mad Scientest
    • View Profile
Re: Issue with digging upwards?
« Reply #5 on: October 29, 2007, 08:49:00 pm »
To build up you need to place the ramp and have a spot for your miners to go when digging. If beside a cliff try rewalling, in the mountain, no clue.
Logged

Griz

  • Bay Watcher
    • View Profile
Re: Issue with digging upwards?
« Reply #6 on: October 29, 2007, 08:53:00 pm »
I built stairs going up by building the up-stairs on the ground floor, holding something against the screen to mark which tile it was, and then going up a level and designating the tile above the up-stairs to have a down-stairs built.

it is quite annoying and would be much better if it worked like the down-stairs where it shows a wall at the end of the stairs.

Logged