Bay 12 Games Forum

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Can I check for magma after Ive started?  (Read 979 times)

Elvin

  • Bay Watcher
    • View Profile
Can I check for magma after Ive started?
« on: May 04, 2009, 07:55:20 am »

Well, I've started a new fortress, i'm fairly certain that I ticked " magma pipe" as a requirement when I looked for this site, but after excavating 10 or so levels below the ground and not finding one i'm not so certain. So is there a way to check for one?

Thanks
Logged

Shoku

  • Bay Watcher
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #1 on: May 04, 2009, 08:12:27 am »

Not specifically but there's an exploity way to locate underground features.
Spoiler (click to show/hide)
Logged
Please get involved with my making worlds thread.

Scarpa

  • Bay Watcher
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #2 on: May 04, 2009, 12:11:30 pm »

I use 3Dwarf with hidden tiles enabled to find features like that. It lets you get a good look at the general area but you still have to poke around a bit in game. Also avoids screwing up your save like reveal does.
Logged

Puck

  • Bay Watcher
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #3 on: May 04, 2009, 12:21:45 pm »

Does the thing with the depot still work?

Smew

  • Bay Watcher
  • I'll kill you with my bear face.
    • View Profile
    • Deep Games for Deep Gamers
Re: Can I check for magma after Ive started?
« Reply #4 on: May 04, 2009, 12:29:08 pm »

Yup, it works just fine.

Puck

  • Bay Watcher
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #5 on: May 04, 2009, 12:49:33 pm »

And there was me, drilling exploratory shafts all over the place just to be able to place my friggin smelter. I feel stupid now.

Samyotix

  • Bay Watcher
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #6 on: May 04, 2009, 12:56:18 pm »

@Puck: Think of it as playing hard mode, without cheats  ;D

The method I used ... Start game. Backup the save folder. Run the game and reveal.exe (found it on the Wiki). Make notes on paper ("where are teh irons?") + save a couple of screenshots so I'd find the magma pool again. Quit, restore save game.

(I did not know the much faster Depot method ... oh well I'll try that after the next release.)
Logged

Albedo

  • Bay Watcher
  • Menacing with spikes of curmudgeonite.
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #7 on: May 04, 2009, 02:18:23 pm »

@Puck: Think of it as playing hard mode, without cheats  ;D

I'm not sure I would call one drill site, a few levels down, in the middle of each area block "hard". 

Or, just go back to a clean copy of your world folder (you saved one, right?) and re-find the same location (you made notes, right?).  NM - you made a couple notes about the map before you embarked, where everything was... right? 

Shouldn't have to go more than maybe 6 levels down, usually half that at most.  Magma is large, a rough circle about 20-25 tiles in diameter, and it has to be completely within the area block.  Big easy target, esp if you include the obsidian that's around it, so it's hard to miss if you drill the center of each block. 
Logged

Puck

  • Bay Watcher
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #8 on: May 04, 2009, 02:29:54 pm »

It aint hard at all, it's just a pita.

Albedo

  • Bay Watcher
  • Menacing with spikes of curmudgeonite.
    • View Profile
Re: Can I check for magma after Ive started?
« Reply #9 on: May 04, 2009, 02:31:23 pm »

<shrugs, nods>
Logged